Loading Special Stock for Proper Finishing Output
Depending on the finishing devices that are present on your system, special paper stock must be loaded in certain ways to achieve correct output. To ensure correct output and to avoid manual collation, load as indicated by the labels on each paper tray and follow the guidelines below.
If you are using a 2 Tray Sheet Feed Module, follow the guidelines for loading stocks in trays 3 and 4.
![]() |
|
![]() |
NOTE: As an aid to you, there are illustration decals on each paper tray which will help you to load stock correctly. |
![]() |
NOTE: For best results and most efficient operation, load special stocks LEF in the paper trays. Loading special stocks SEF may result in pages delivered with incorrect rotation and face-up or face-down delivery. Special programming may be required to correct. |
Systems with SFM and/or Insertion Module and BFM
Stock Type |
Loading |
|
Drilled paper |
Trays 1 and 2 |
Holes leading |
Trays 3 and 4 |
Holes leading |
|
Labels |
Trays 1 and 2 |
Label side up |
Trays 3 and 4 |
Label side up |
|
Tabs (forward collated tabs only) |
Trays 1 and 2 |
Tabs trailing - face up |
Trays 3 and 4 |
Tabs trailing - face up |
|
Preprinted stock |
Trays 1 and 2 |
Face up, left edge leading |
Trays 3 and 4 |
Face up, left edge leading |
|
Transparencies |
Trays 1 and 2 |
Tape edge leading |
Trays 3 and 4 |
Tape edge leading |
|
Ordered stock |
Trays 1 and 2 |
Face up, 1-N order |
Trays 3 and 4 |
Face up, 1-N order |
Systems with MFF ONLY
Stock Type |
Loading |
|
Drilled paper** |
Trays 1 and 2 |
Holes trailing |
Trays 3 and 4 |
Holes trailing |
|
Labels |
Trays 1 and 2 |
Label side up |
Trays 3 and 4 |
Label side up |
|
Tabs** (reverse collated tabs only) |
Trays 1 and 2 |
Tabs trailing - face up |
Trays 3 and 4 |
Tabs trailing - face up |
|
Preprinted stock |
Trays 1 and 2 |
Face up, right edge leading |
Trays 3 and 4 |
Face up, right edge leading |
|
Transparencies |
Trays 1 and 2 |
Tape edge trailing |
Trays 3 and 4 |
Tape edge trailing |
|
Ordered stock |
Trays 1 and 2 |
Face up, right edge leading, 1-N order |
Trays 3 and 4 |
Face up, right edge leading, 1-N order |
**Special Case: Jobs with drilled paper AND drilled tabs when using the MFF:
When processing jobs which use drilled paper and drilled tabs together, load the tabbed stock with tabs trailing as usual, but load the drilled paper stock with the holes leading. This is contrary to what the label on the tray depicts, but drilled stock must be loaded this way in order to achieve correct output. If the job includes drilled tabs or drilled paper, but not within the same job, follow the diagram on the tray label and/or the information in the table above.
Systems with SFM Insertion Module and MFF Professional
![]() |
NOTE: No tabs can be loaded into an SFM Insertion Module (if present) if using a MultiFunction Finisher. |
Stock Type |
Loading |
|
Drilled paper |
Trays 1 and 2 |
Holes trailing |
Trays 3 and 4 |
Holes trailing |
|
Labels |
Trays 1 and 2 |
Label side up |
Trays 3 and 4 |
Label side up |
|
Tabs |
Trays 1 and 2 |
Tabs trailing (loaded into pre-fuser FM only) |
Trays 3 and 4 |
Tabs trailing (loaded into pre-fuser FM only) |
|
Preprinted stock |
Trays 1 and 2 |
Face up, right edge leading |
Trays 3 and 4 |
Face up, right edge leading |
|
Transparencies |
Trays 1 and 2 |
Tape edge trailing |
Trays 3 and 4 |
Tape edge trailing |
|
Ordered stock |
Trays 1 and 2 |
Face up, right edge leading, 1-N order |
Trays 3 and 4 |
Face up, right edge leading, 1-N order |
Systems with MFF Pro Plus ONLY
Stock Type |
Loading |
|
Drilled paper** |
Trays 1 and 2 |
Holes trailing |
Trays 3 and 4 |
Holes trailing |
|
Insertion Tray |
Holes trailing |
|
Labels |
Trays 1 and 2 |
Label side up |
Trays 3 and 4 |
Label side up |
|
Insertion Tray |
Label side up |
|
Trays 1,2,3,4: reverse collated tabs only ** Insertion Tray: forward collated tabs only |
Trays 1 and 2 |
Tabs trailing - face up |
Trays 3 and 4 |
Tabs trailing - face up |
|
Insertion Tray |
Tabs leading - face up |
|
Preprinted stock |
Trays 1 and 2 |
Face up, right edge leading |
Trays 3 and 4 |
Face up, right edge leading |
|
Insertion Tray |
Face up, right edge leading |
|
Transparencies |
Trays 1 and 2 |
Tape edge trailing |
Trays 3 and 4 |
Tape edge trailing |
|
Ordered stock |
Trays 1 and 2 |
Face up, right edge leading, 1-N order |
Trays 3 and 4 |
Face up, right edge leading, 1-N order |
|
Insertion Tray |
Face up, right edge leading, 1-N order |
More information about tabbed stocks
For more information, see Printing/Copying on Tabbed and Ordered Stock.